100% stainless steel. Built with 100% stainless steel, AlfaNova® is a solution that Alfa Laval offers for applications that use media not compatible with traditional heat exchanger materials. Not only is this advanced design optimized for use with natural refrigerants, its also completely recyclable. Brazetek Heat Exchanger Applications by IndustryBrazed Plate Heat Exchangers. A brazed plate heat exchanger from Brazetek offers effective means of heating water for domestic use by exchanging heat with boiler water, water from a solar system or many others. The maximum efficiency of a heat exchanger is achieved when plumbing both liquids to flow in counter current directions.
Our plates come with a double gasket at the inlet and outlet to prevent mixing of the two media. If designed as a safety heat exchanger, double plates are provided with a special gasket system. Special series. Safety plate heat exchangers (FPDW) Stainless steel versions for FUNKE TPL PDF - New PDF OptionsMay 18, 2020 · The plates are assembled in a ° angle to each other. FUNKE brazed plate heat exchangers series TPL is basically made of non- corrugated stainless steel plates. In the flow gaps special stainless steel turbulence. User instructions. These instructions relate to the standard versions of the brazed FUNKE plate heat exchanger (PWT). Funke Heat Exchanger Gaskets & Plates HFMHFM Plate Heat Exchanger Gaskets & Plates. HFM manufactures and supplies high quality PHE spare parts, rubber gaskets and metal plates. The customized dimension mould pressing and non-OEM but 100% compatible replacement of full models . are both available to meet client's different requirements.
If designed as safety heat exchanger, double plates are provided with a special sealing system. Plate material:standard:stainless steel 1.4301/AISI 304, 1.4401/AISI 316 Optionally:1.4539, 254 SMO, titanium Gasket material:NBR (nitrile-rubber) EPDM (ethylene-propylene-rubber) Viton (fluorine-rubber) Further materials on request JiaWei Plate Heat Exchanger is a reliable China supplier For single pass Plate Heat Exchangers start and flow plates are often 4-hole while the end plate is 0-hole. Plate Corrugation . Plate Material. 304 Stainless Steel This is the lowest cost heat transfer plate material. It has a low corrosion resistance and is typically available in thickness from 0.5mm up to 0.7mm. This type of heat transfer plate Plate Heat Exchanger - HRSFUNKE HEAT TRANSFER FZEFor HRS FUNKE, the off-set profile represents an additional control we can equip your plate heat exchanger with the following accessories: insulations (e.g. mineral insulating material covered with CIP cleaning system frames made of stainless steel or in stainless steel cladding PHE as twin cooler with changeover
Heat exchanger plates The plate pack is mounted in a rack and FUNKE heat transfer plates are always produced in 1.4401/ AISI 316L as this material is generally more corrosion-resis-tant and more resistant to chloride damage than 1.4301/AISI frames made of stainless steel Plate Heat Exchanger|Gasket Plate Heat Exchanger|Brazed HRSFUNKE heat transfer plates are characterised by optimum embossing, which leads to high heat transfer coefficients. This results in a low cost heat exchanger which achieves the best possible performance irrespective to the application conditions. Our product range includes single-pass and multi-pass plate heat exchangers with a heat exchange surface of up to 2000 m². Plate heat exchanger_Plate heat exchanger_Funke Heat FSheet bar bundle of a Funke brazed plate heat exchanger is made of pressed stainless steel; with copper or nickel foil of purity over 99.9%, heated and brazed in a vacuum furnace. Besides, the plates
Gasketed Plate Heat Exchanger Plate heat exchangers use corrugated plates stacked between a fixed and movable pressure plate. As virtually all of the material is used for heat transfer, plate heat exchangers can have large amounts of effective heat transfer surface in a small footprint. SONDEX® semi-welded plate heat exchangersThe heat exchanger is designed to be highly resistant to thermal shocks as well as thermal and pressure fatigue making it very well-suited for cyclic duties and other duties with sudden, large fluctuations in temperature. Copper, copper+, or stainless steel; Plate materials:AISI 316* Plate heights from 0.202 m to 1 m (0.66 3.3 ft) Flow STAINLESS STEEL HEAT EXCHANGER PLATES, Gasketed Plate Platex India - Offering STAINLESS STEEL HEAT EXCHANGER PLATES, Gasketed Plate and Frame at Rs 250/piece in Pune, Maharashtra. Read about company. Get contact details and address
Stainless steel is non-corrosive and can tolerate external influences like lime, water, bacteria and dirt. Due to his low melting point and its stronger expansions after contact with heat, welding stainless steel needs highly-experienced workers with much experience. Stainless steel plate heat exchanger Stainless steel SPX Flow Technologies heat exchanger by FRICK LaZerWeld. Has a National Board No 15675 and a manufactures serial no:G2014000664; Plate ID:LZWX-400 and was built in 2014. Max WP in Chamber H1 & H3 is 150 PSIG AT 185° F. Max WP in Chamber H2 & H4 is 300 PSIG AT 185° F. Min. Design Metal Temperature Chamber H1 & H3 -20° F AT 150 PSIG Supply Perfect Replacement Plate Heat Exchanger Plate We can supply a large range of high quality heat exchanger plate for many brands These plates can be exchanged with original plates, and are already widely used in after service strictly control the production and strict delivery inspection.We strictly enforce the requirements of ISO9000, and strictly control every aspect of production, so that
Used- Funke Plate Type Heat Exchanger, Type FP 14-57-1-NH-0. Used- Funke Plate Type Heat Exchanger, Type FP 14-57-1-NH-0, Approximately 45 Square Feet. (30) Stainless steel plates approximately 9-1/2" wide x 28" long. Rated 145 psi (10 bar). Temperature rate 32 to 230 degrees F (0/110 degrees C). Mounted on a painted carbon steel expandable frame. Funke Fp250 Stainless Steel Heat Exchanger Plate - ASTM The vessel, a steam/brine heat exchanger, operated in a radiologically controlled zone (by the CH2MHill PRC or CHPRC), had been in service for approximately 17 years. The heat exchanger is part of a single train evaporator process and its failure caused the entire system to be shut down, significantly impacting facility operations.